|
Young Farm Machinery, Inc. is your Authorized Dealer for H & S Equipment
|
|
Please call 606-849-2677 or email at Jent_24@yahoo.com for complete listing and prices.
|
|
H & S Manure Spreaders
These are some of the best spreaders on the market they come in sizes form 25 Bu. to 3302 Bu. We usually keep the 125, 175, and the 235. Come in and take a look at our spreaders, you wont be disappointed!!
H&S MODEL 125 MANURE SPREADER,
125 BU. PTO DRIVE. THE H.D. HITCH AND FRAME IS BUILT TO WITHSTAND THE STRESS OF HEAVY LOADS AND ROUGH FIELDS. THE JACK IS STANDARD. THE SPREADER BOX IS CONSTRUCTED OF CORROSION RESISTANT GALVANIZED STEEL. ALL SPREADERS UTILIZE A BONDED POLY FLOOR TO REDUCE MAIN APRON DRAG AND POWER TO MOVE THE LOAD.
H&S MODEL 175 MANURE SPREADER,
175 BU. USES AN ALL WELDED HEAVY DUTY A-FRAME HITCH ASSEMBLE AND FULL LENGTH UNITIZED MAIN FRAME. THE JACK IS STANDARD. THE SPREADER BOX IS CONSTRUCTED OF CORROSION RESISTANT GALVANIZED STEEL. ALL SPREADERS UTILIZE A BONDED POLY FLOOR TO REDUCE MAIN APRON DRAG AND POWER TO MOVE THE LOAD.
H&S MODEL 235 MANURE SPREADER,
STRUCK LEVEL 143 CU. FT., 235 BU. UNLOADING SPEED FOR THE 235 SPREADER - (2 SPEED GEAR BOX) HIGH SPEED: PTO SPEED 540 RPM. 8 FT 9 IN PER MINUTE - LOW SPEED: PTO SPEED 540 RPM. 4 FT 9 IN PER MINUTE.
For additional Specifications go to H & S Equipment visit www.hsmfgco.com
|
|
H & S Manure Spreader
This 25 Bu. Ground Driven manure spreader is just what you need if you have just a few head of livestock. The beater on the Model 25 is 20" in diameter and with 8 paddles it provides and even spread of material. It has 5 x 12 Deep Lug Traction tires. It has poly bonded floor just like the larger spreaders.
|
| | H & S V - Rake
The H & S v-rake is available in 8, 10 & 12 wheel models. Ranging from raking widths from 15 feet. to 24 feet. The H & S V Rake has the flexibility to rake with one side only. -USING THE HITCH JACK, THE OPERATOR CAN ADJUST THE WINDROW WIDTH.
A SINGLE ACTING CYLINDER COUPLED WITH A SIMPLE LINKAGE SYSTEM ALLOWS FOR EASY RAISING AND LOWERING OF RAKE WINGS.
RAKING WIDTH ON THE H&S V-RAKES CAN BE ADJUSTED TO 3 DIFFERENT POSITIONS WITH THE PIN AND FINE TUNED BY ADJUSTING THE TURNBUCKLE SCREW.
THE OPERATOR CAN ADJUST THE FINE TUNE SPRING TO ALLOW PROPER RAKE WHEEL DOWN PRESSURE.
FOR MORE Specifications CLICK HERE www.hsmfgco.com or email us at jent_24@yahoo.com or call 606-849-2677.
|
| H & S Hi-Capacity Bi-fold Rake
THE H&S HI-CAPACITY BI-FOLD RAKES HAVE THE RAKING WHEELS POSITIONED AHEAD OF THE RAKE ARMS, MAIN FRAME BEAMS AND TRANSPORT WHEELS. COUPLED WITH A HIGH AND WIDE END OF FRAME THERE ARE NO HANG UP POINTS OR RESTRICTIONS WHEN RAKING THE HEAVIEST OF HAY CROPS.
H&S HI-CAPACITY RAKES FOLD UP TO 8'6'' OR LESS WITH THE TOUCH OF A LEVER FOR ROAD TRANSPORT OR TO GO THROUGH GATES\
THE RAKE ARMS ON THE 14 WHEEL HI-CAPACITY RAKES FEATURE 2 ROLLER BEARINGS ON EACH END OF THE ARM FOR LONG LIFE, SMOOTH OPERATION AND LESS WEAR THAN RAKES WITH BUSHINGS.
LIMITED OSCILLATING OFFSET TANDEM TRANSPORT WHEELS ASSURE A SMOOTH, LEVEL RIDE, EVEN OVER IRRIGATION TRACKS. TANDARD ON THE 14 WHEEL HI-CAPACITY
THE HI-CAPACITY RAKE CAN BE CONFIGURED AS BOTH A V-RAKE OR WITH THE RIGHT SIDE OPEN AS A TRAILER RAKE.
THE ADJUSTMENT FOR THE GROUND PRESSURE ON THE RAKE WHEELS ALLOWS THE OPERATOR TO FINE TUNE THE 14 WHEEL HI-CAPACITY RAKE TO FIT VARYING CONDITIONS.
THE HI-CAPACITY RAKE OPENS AND CLOSES HYDRAULICALLY, RAKE WHEELS ARE LOWERED AND RAISED HYDRAULICALLY, AND THE RAKE WHEELS FLOAT INDEPENDENTLY. THE HIGH OPEN, ADJUSTABLE REAR FRAME ALLOWS FOR THE HEAVIEST CROP TO PASS THROUGH. WINDROW WIDTH ADJUSTMENT IS DONE WITH A HAND CRANK.
AN ADJUSTABLE BRAKE BAND ON TOP OF THE FRONT SPINDLE KEEPS THE FRONT GAUGE WHEELS SPINNING IN ROUGH CONDITIONS
|
| H&S Hydraulic bi-fold Rakes
H&S 8, 12 1ND 16 WHEEL HYDRAULIC OPEN MODELS ARE STANDARD WITH A RATCHET TYPE ADJUSTABLE JACK TO SET WINDROW WIDTH SETTINGS.
ALL H&S BI-FOLDS UTILIZE A SINGLE ACTING CYLINDER TO LIFT RAKING WHEELS FROM RAKING TO TRANSPORT POSITION. CYLINDERS CAN BE COVERTED TO DOUBLE ACTING. THE RAKE WHEELS ARE INDEPENDENTLY MOUNTED AND SPRING LOADED TO FOLLOW THE CONTOURS OF THE GROUND. ALL BI-FOLD RAKE ARMS ARE DESIGNED WITH OVER CENTER LIFT STOPS.
A RAKE BEAM TRANSPORT POSITION RAMP AND ROLLER IS UTILIZED ON ALL HYDRAULIC MODELS. AS THE ROLLER IS ELEVATED UP THE RAMP, THE RAKE ARMS AND GAUGE WHEELS LIFT OFF THE GROUND INTO TRANSPORT POSITION
THE HYDRAULIC OPEN BI-FOLDS REAR CROSSMEMBERS ARE ROUND. THIS FEATURE ALLOWS THE RAKE ARMS TO FLOAT, ALLOWING THE OPERATOR TO RAKE FLAT OR ROLLING GROUND AS WELL AS WATERWAYS, DITCHES AND TERRACES. RATCHET JACKS PROVIDE FOR EASY ADJUSTMENT OF FINISHED WINDROW WIDTHS.
ALL BI-FOLDS CAN BE OPERATED WITH ONE SIDE OUT WHILE THE OTHER IS FIXED IN TRANSPORT POSITION.
|
|
H&S HIGH QUALITY ROUND BALE TRANSPORTS
UPRIGHTS KEEP THE BALES FROM SLIPPING OFF THE BALE CRADLE. 6' LONG QUICK HITCH TONGUE AND TRICYCLE TYPE STEERING ENABLES THE OPERATOR TO LOAD A BALE ON A 3-POINT ROUND BALE FORK AND STILL HOOK THE BALE TRANSPORT UP TO THE TRACTOR.
6' HIGH GUIDE RODS ALLOW THE OPERATOR TO SEE FOR EASE OF LOADING. THE CENTER BEAM IS MADE OF STRONG
4'' X 8'' X 3/16'' STEEL TUBING. BALE CRADLE ARMS ARE 3/16'' SQUARE TUBING, REINFORCED WITH GUSSETS, AND TIED TOGETHER WITH A FLAT METAL STRAP TO KEEP THEM FROM SPREADING.
|
|
